AVI Laboratory Series Integrated Amplifier






Specifications:

  • Frequency Response: (-3dB) <1.5Hz - >250Khz
  • Input Impedance: 14k Ohms
  • Input sensitivity: (150W into 8 Ohms, 1kHz) 530mV
  • Tape Output Level (at rated sensitivity): 530mV
  • S+N/N Ratio Unweighted: 96dB
  • S+N/N Ratio IEC “A”: 112dB
  • Absolute Phase: +VE
  • AC Mains supply (factory pre-set): 110v-120v, 220v-240v
  • AC Mains consumption: 1000W max.
  • Dimensions (W X D x H): 315 x 350 x 95mm
  • Shipping dimensions (W X D X H): 400 x 440 x 170mm
  • Gross weight: 12.8Kg

    Maximum Power Output (One channel driven):
    8 Ohms, 1kHz, 1% distortion 200W
    4 Ohms, 1kHz, 1% distortion 325W
    2 Ohms, 1kHz, 1% distortion (note 1) 480W

    Maximum Power Output (Both channels driven):
    8 Ohms, 1kHz, 1% distortion 175W
    4 Ohms, 1kHz, 1% distortion 300W
    2 Ohms, 1kHz, 1% distortion (note 1) 420W

    Distortion (T.H.D., 1kHz, -1dB below full power):
    8 Ohms <0.002%
    4 Ohms <0.002%



 

We have called the new amplifier the Laboratory Series because it is a development (albeit a meticulous and painstaking one) of the amplifiers we use to evaluate our loudspeakers. It is particularly important that an amplifier being used for such a purpose is immune to the effects of the speaker, has negligible distortion and sufficient dynamic range to avoid clipping on the transients in music. We want to hear the music not an inadequate amplifier!

There are six inputs with the option of a phono stage (more on that later), the tape loop is buffered and it is possible to record one source while listening to another. Volume control is by a large bead blasted aluminum knob (to provide the correct feel) and the front panel has accurate graduations to ensure its precise location. When controlled by the remote handset, a dab of the button will produce changes of a 1/2 dB!

Power output into 8 ohms is a conservatively rated 200 WPC and this almost doubles into 4 and 2 ohms. Enormous current is available ensuring that the largest and most complex speakers are driven with ease and that low frequency control and dynamics are displayed to perfection. If the amp is shorted, protection is swift as it is if the load drops to a little over 1 ohm.

The most sensitive ear applied to the most sensitive loudspeaker may just be able to hear background noise. Distortion is lost in the noise generated by most test equipment!

This is one of the finest sounding amplifiers you are going to hear, regardless of your budget!

AVI is for serious music enthusiasts and for many this means they must still be able to play irreplaceable vinyl and play it to the highest standard that technology permits. We have designed a factory fittable phono stage that is switchable (via a switch in the rear panel) to either moving coil or moving magnet cartridges. For those with the finest, we can alter the input to precisely match it. There is a modest additional charge for this service.

The Laboratory Series Integrated Amplifier is much larger and heavier than its pre-decessors; it is built from large chunks of milled aluminum and thick steel sheet to ensure mechanical rigidity and absolute integrity of construction. The huge heat sinks are anodized in black as is the front panel and top cover. The controls and the graphics are in contrasting silver.

AVI has chosen very high performance bi-polar output devices. They have a 50mMHz power bandwidth! Although they are more difficult to use, it is generally agreed that they sound a little more "musical" than Mosfets. Experience has shown that the slightest imperfections of sound, once noticed, become major irritants and quickly alienate listeners. Our reputation for outstanding sound quality is very precious to us and we have taken trouble to ensure that no such defects are present in any of our products.

Our new Laboratory series Integrated amplifier will compliment the present range and form the basis of an entirely new range of High End electronics, all of which should be in the shops during next year.

 
Untitled Document

audio | home theater | accessories | product lines | used gear | contact us
about overture audio | home

 
Overture Audio
Ann Arbor, Michigan 48104
Phone: 734-662-1812